Watch our video on how to build your

Distributor Display Stand

Your DRYFT Distributor Display Stand is designed to elevate your presence - and mastering its setup is the first step to unlocking its full potential. By learning how to assemble the stand confidently and correctly, you ensure that every demonstration looks professional, polished, and true to the premium standard of the DRYFT brand. The build process is quick, intuitive, and requires no special tools, making it easy for any team member to set up.

Invest a few moments in learning the assembly, and you'll be able to showcase your DRYFT products with maximum impact wherever you go. A well-built display doesn’t just present your products; it elevates your entire brand image. Let’s get started!

Step-by-step instructions

  • 1. Identify the correct orientation of the lightbox wall.

    You should build the unit with the feet where it will stand, allowing a 2-meter leeway from any walls or hard surfaces.

    • Lay out the aluminium panels on the floor (note that the floor and ceiling pieces contain LED strips). 

    • Make sure to identify each part, and the difference in the sides/floor pieces. 

  • 2. Connect each side together.

    • Ensure the correct sides have connected properly and are secure. 

    • Ensure that the magnetic pin is connected on both sides of the LED strip. 

  • 3. Slide on TV bracket to the ceiling piece, facing upwards.

    • You may need to slide this on from the middle of the ceiling piece by disconnecting it first. 

    • Make sure that both pieces of the bracket are hung correctly. 

    • Do not fully secure the TV bracket, in case of needing adjustment. 

  • 4. Connect the ceiling pieces to the sides to create the frame.

    Ensure to secure each corner. 

  • 5. Attach the supports and click into place.

    Ensure you place the two types in the correct orientation. 

  • 6. Connect the bottom pieces to the sides and connect the LED wiring.

    • Make sure the frame is secure. 

  • 7. Locate the front graphic and check the pre-cut holes.

  • 8. Place the graphic over the frame ensuring the holes align with the TV bracket.

  • 9. Begin pushing the graphic into place until it is taught with no loose sides.

  • 10. Slide in the feet, ensuring the pathway is clear, and press the connector firmly down.

    • Make sure the connector grips the feet in place securely. 

    • The feet should be flush with the bottom of the frame. 

    • You may need to remove the corner of the graphic to get a clear view. 

  • 11. Lift the stand onto its feet.

    Please be aware of your own manual handling and the safety of others. 

  • 12. Check the structure and secure if needed.

    Everything should now look aligned and stable. 

  • 13. Check the alignment of the TV bracket against the pre-cut access holes in the graphic.

    • Adjust the bracket where necessary by sliding the bracket across the ceiling. 

    • Secure the TV bracket in place by tightening the bolts. 

  • 14. Attach the brochure holder within the mouth of the frame by placing it onto the graphic and securing the mount from behind.

    • The mount should sit in the mouth of the TV bracket, placing the weight against the TV bracket not the graphic. 

  • 15. Place the TV through the pre-cut holes vertically and secure onto the bracket using the wingnuts from behind.

    • You may need a second person to do this. 

    • Ensure the power cable is at the top of the TV. 

  • 16. Wire all cables through the access ports.

  • 17. Plug in the frame LEDSs and the TV to power outlets using reasonable caution.

  • 18. Turn on the TV and load the content using the USB stick.

  • 19. Add the brochures to the holder and check its stability.

  • 20. Add the back graphic if needed, by pushing in the sides of the graphic as before.

    • Be aware of cabling when moving around the frame. 

    • You may need a step stool, ladder, or second person to reach the top of the frame comfortably. 

  • 21. Roll out the floor mat

    Secure to the floor if possible. 

  • 22. You’re ready to showcase DRYFT!

  • 1. Identify the correct orientation of the lightbox wall.

    You should build the unit with the feet where it will stand, allowing a 2-meter leeway from any walls or hard surfaces.

    • Lay out the aluminium panels on the floor (note that the floor and ceiling pieces contain LED strips). 

    • Make sure to identify each part, and the difference in the sides/floor pieces. 

  • 2. Connect each side together.

    • Ensure the correct sides have connected properly and are secure. 

    • Ensure that the magnetic pin is connected on both sides of the LED strip. 

  • 3. Slide on TV bracket to the ceiling piece, facing upwards.

    • You may need to slide this on from the middle of the ceiling piece by disconnecting it first. 

    • Make sure that both pieces of the bracket are hung correctly. 

    • Do not fully secure the TV bracket, in case of needing adjustment. 

  • 4. Connect the ceiling pieces to the sides to create the frame.

    Ensure to secure each corner. 

  • 5. Attach the supports and click into place.

    Ensure you place the two types in the correct orientation. 

  • 6. Connect the bottom pieces to the sides and connect the LED wiring.

    • Make sure the frame is secure. 

  • 7. Locate the front graphic and check the pre-cut holes.

  • 8. Place the graphic over the frame ensuring the holes align with the TV bracket.

  • 9. Begin pushing the graphic into place until it is taught with no loose sides.

  • 10. Slide in the feet, ensuring the pathway is clear, and press the connector firmly down.

    • Make sure the connector grips the feet in place securely. 

    • The feet should be flush with the bottom of the frame. 

    • You may need to remove the corner of the graphic to get a clear view. 

  • 11. Lift the stand onto its feet.

    Please be aware of your own manual handling and the safety of others. 

  • 12. Check the structure and secure if needed.

    Everything should now look aligned and stable. 

  • 13. Check the alignment of the TV bracket against the pre-cut access holes in the graphic.

    • Adjust the bracket where necessary by sliding the bracket across the ceiling. 

    • Secure the TV bracket in place by tightening the bolts. 

  • 14. Attach the brochure holder within the mouth of the frame by placing it onto the graphic and securing the mount from behind.

    • The mount should sit in the mouth of the TV bracket, placing the weight against the TV bracket not the graphic. 

  • 15. Place the TV through the pre-cut holes vertically and secure onto the bracket using the wingnuts from behind.

    • You may need a second person to do this. 

    • Ensure the power cable is at the top of the TV. 

  • 16. Wire all cables through the access ports.

  • 17. Plug in the frame LEDSs and the TV to power outlets using reasonable caution.

  • 18. Turn on the TV and load the content using the USB stick.

  • 19. Add the brochures to the holder and check its stability.

  • 20. Add the back graphic if needed, by pushing in the sides of the graphic as before.

    • Be aware of cabling when moving around the frame. 

    • You may need a step stool, ladder, or second person to reach the top of the frame comfortably. 

  • 21. Roll out the floor mat

    Secure to the floor if possible. 

  • 22. You’re ready to showcase DRYFT!